Premium spring seals factory supplier: The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film. Read additional info at rod seals manufacturer.

A mechanical seal is a very effective device. Every centrifugal pump must accommodate a spinning shaft while mechanically maintaining fluid or gas contained in the “wet end” of the pump. Mechanical seals consists primarily of a rotary seal face with a driving mechanism which rotates at the same speed as the pump shaft, a stationary seal face which mates with the rotary and is retained using a gland or in some pump models an integral stuffing box cover, a tension assembly (utillizing springs or a metal bellows) keeps the rotary face firmly positioned against the stationary face preventing, excluding, and containing contamination and leakage, both when the pump is not in operation and when the pump shaft is rotating. Static sealing gaskets, orings or elastomeric bellows are strategically located to complete the seal assembly.

Key points of engineering mechanical seal design: Select a reasonable sealing scheme, focusing on the above requirements. First of all, the dustproof performance must be good. More than 80% of the failures of the hydraulic system are directly or indirectly derived from the stains in the system. Choose the best seals For seals of the same structure, the product quality of each company varies greatly. On the whole, the quality of large foreign seal companies is relatively stable, but the probability of encountering fakes is too high. Sometimes the so-called direct supply is not reliable. In terms of domestic seals, most of them are not very good, but at present, some manufacturers’ products have been chasing or even surpassing imported products, with stable and reliable quality, such as tetrafluoroethylene and rubber seals produced by Damson Sealing.

It is ideal for single-acting sealing of reciprocating piston rods or pistons with a wide operating pressure range of up to 20 MPa. The operating temperature range is also wide from -200°C to + 250°C. It has a diameters range from 3 mm to 1600 mm and a working speed of 5 m/s. The seal has a low coefficient of friction and the friction between the contact faces is minimal among all seal types. Moreover, the contact pressure between the mating surfaces is low. It can work without lubrication and is very wear resistant. And it has a long service life.

Rubber seals are a common type of basic component in sealing devices, and play a very important role in the contradiction between leakage and sealing. Using rubber seals is an important way to promote technological advancement and prevent and reduce environmental pollution. They are a class of rubber products that are widely used in sealing technology. Because rubber is a polymer material with valuable elasticity, a wide temperature range. It gives less stress in different media producing large deformation, which can provide contact pressure, compensate for leakage gap, and achieve the purpose of sealing.

Our piston seals are designed to provide excellent leak control. We guarantee that it can perfectly meet the user’s requirements for low friction, compactness, precise configuration and simple installation. It is designed for fluid power applications. It is made of compound materials with high performance, which guarantees excellent wear resistance and excellent extrusion resistance for the seal. It is designed to be suitable for almost all fluid media and is highly resistant to oxidation and corrosion. It has excellent dynamic and static sealing performance and can even work under dusty industrial environments. Moreover, it has strong adaptability to various working conditions and can adapt to a fast, high-pressure working environment. At the same time, it has unparalleled performance in extreme temperature environments.

The selection principle of the gasket: according to the working pressure, working temperature, the corrosiveness of the sealing medium and the form of the sealing surface. Temperature influence: In normal temperature and low pressure, use non-metallic soft honey gasket; in medium pressure and high temperature, choose metal and non-metal combination gasket or metal gasket; when temperature and pressure fluctuate greatly, choose good elasticity or self-tightening type Gaskets; in low temperature, corrosive media or vacuum conditions, gaskets with special properties should be considered.

We own a number of invention patents and leading production process. The R&D teams have the ability to design and develop seals for various of complicated working condition of sealing system. We have already passed the certification of ISO 9001 and IATF 16949. We have the mature technical reserve for the solution of ultra-high temperature, ultra-high pressure, ultra-low temperature, highly corrosive and other special working condition. Find additional details at https://www.dmsseals.com/.

DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.